Side by Side Comparison of: Foam It Green vs 3M

Super great kit, used as much as 10 cans of the regular single part stuff, but still not quite large enough. It does not get near as warm as they would have you believe.

Worked very well for a small project that I had sealing up some floor joist. Easy to use and a very small wand to get into hard to reach spaces.

I got this kit to fill in an area of my basement where mice had been getting in and where I had traditionally had a draft. Not only was it easy to use, but I haven't had a need for one mouse trap since and the draft is now gone. The directions were easy enough to follow, but the video they sent me in my confirmation email made it even more seamless. I'm thinking about finishing the rim joist area with one of the larger kits since I have a lot more square footage, but I recommend this kit for any smaller jobs around the house. Easy to use kit, great product, great service and easy to follow directions. Will definitely use Foam It Green again!

I used the Foam It 12 to spray the underside of a small section of floor that is always cold.The kit contained complete instructions and the company even has a how-to video on their website to show you how to set up the kit.The Foam It 12 was just the right size for my small project. It was super easy to use and I was able to finish my project quickly.I'm sure I'll find other spots around the house that could benefit from a little foam insulation, and when I do, I'll be using Foam It Green.

GRATE PRODUCT

This product worked great for me to insulate under a bump out bay window. There is a noticeable difference on the inside now.

I used larger kits from this company and had great result with my rim joist area. I had to cut into the existing foam to do some plumbing work so I needed to replace what I had to take out and the 12 kit was the perfect size. I read the the direction on the box and watched the video on their website and it was done right away. Highly recommended.

Followed instructions on the box, watched the online video, dispensed the foam. Foam stuck to the intended surface and was hard/dense when cured. Did not use a dropcloth since I didn't care about the floor, but would recommend it if you do.

Got great results using this kit. Before I used the kit I went over the instructions and watched the instructional video on the Foam It Green website so I would know how to get the best results. It's a really easy system, basically you spray it on thin, it rises and cures in about 5 minutes and I was sure i got the ratio right because the foam was green.

I've used a lot of Foam It product and loved it -- once I got the feel of it. This stuff was different. The first 50% came out OK but then it was like there wasn't enough pressure to push the chemicals. I shook the containers plenty and they had been at almost 80 degrees for several days. As I've learned to do with the big kits, I laid my pattern out carefully so I didn't need to lift the trigger or waste any foam. I was still getting both chemicals when things went bad but it just sputtered instead of spraying.

I was a little disappointed in the net amount of foam I got for the money. However, I was spraying up into a vaulted ceiling area which was challenging.

The cheap plastic handle that you are supposed to use to turn it on broke during the simple act of switching it on. Saw another review that said the same, wish I had listened. It was useless after that, as the little plastic piece is supposed to hold down the lids from the bottle inside.

Update: the company tracked me down and refunded me the money even though I did not contact them to do so. They seemed genuinely interested in the issues I had with the handle. Hopefully they will remedy that aspect of the product, but at least they stand behind it and are attentive to the customer.

Since they went the extra mile, I think I would give them another shot if I need a product like this again. If you purchase, just be very careful to follow the directions and handle the plastic "switch" gently.

The foam itself seems to be exactly what you would want/expect and the little bit I was able to use hardened up firmly.

I made sure the box was retained with the cans upright according to the arrow printed on the box.I did this by strapping the box to a chain link fence so it could not turn over.After spraying about 1/2 to 2/3 of the material the only thing that sprayed was the blue material.the other material was totally run out.Blue material alone does not foam and does not get hard.I would not ever buy another product from this company as there is no way to know how well it will work.Since there is no way to determine if you will get your money's worth I would recommend you purchase from some other company.

I tried this product for the underside on floor joists that were always cold in winter. I figured it was a good trial before spending the thousands for the larger kits for the whole underside of the floor. As a previous reviewer stated, covering 12 sqft was not even close to what it did. The nozzle was hard to control the flow with, and the product didn't discharge away from the nozzle more than a couple inched. I ended up covering about 4 sqft, and it is not a solid covering. I was very disappointed.

The cans were empty within 30 seconds. Did not cover half the area as advertised. A complete waste of money!

I tried two of the Foam It 12 units. One of the units worked fine, although there was little control over the flow of the foam. The mechanism includes a small roller that pinches the tubes carrying the foam components -- but this was not capable of shutting off the flow. So basically once you started it, it kept going until the cans were discharged. Unfortunately, this meant I wasted about 30% of the foam because I wasn't able to properly direct the stream.One of the units completely failed, with parts missing and the warranty was not honored by the company.I would not recommend this product, and would suggest trying some of the very similar products by more reputable manufacturers.